Acrylic Awards

 

METHODS AND DIFFERENCES IN NAME BADGE PRODUCTION AND COSTS

Click Here to see color choices available

Click Here for corporate logos

One and two line engraving on flat plastic surfaces (above) is typically the least expensive method of name identification. To keep costs low, adding a pin back attachment is most effective and least costly. 20 letter maxium Name badges manufactured with this process can be as low as $3.00 each in quantity (100 minimum plus shipping and tax where applicable). Other attachments include swivel clips (.30 ea.) , military post backs (.40 ea.) and magnets (.99 ea.). See photos at bottom of this page
DESCRIPTION
STYLE #
OVERALL SIZE (WxH)
ENGRAVABLE AREA
PRICE
NAME BADGE
1 LINE ENGRAVING
1" X 3"
3/4" X 2 3/4" APPROX.
$4.00
QTY:
2 LINES ENGRAVING
$4.75
QTY:
3 LINES ENGRAVING
$5.25
QTY:
 

Minimum order for above badge is 100 w/ maxium 15 letters (including pin back) + S&H- No discounts for multiple orders.*Any other size available and your size, shape, color and quantity will be quoted upon request.

 

Adding corporate logos (above), religious and fraternal emblems and corporate I.D's. usually requires a minimum of two "passes" with the laser or engraver. The first is to laser or engrave the logo. By doing this initially it establishes same size settings for all the badging keeping your I.D. uniform in appearance as well as mass producing the badge quickly. Next, names are lasered or engraved whether it is one, two or (in some cases) three lines. Because of the extra pass, cost is typically a little higher with the logo or emblem than without it, however, cost is not that much more and the results are tremendously enhanced. Send us your proposed name badge for a free quote or e-mails us @ info@naplenco.com.
DESCRIPTION
STYLE #
OVERALL SIZE (WxH)
ENGRAVABLE AREA
PRICE
NAME BADGE
1 LINE ENGRAVING
1" X 3"
3/4" X 2 3/4" APPROX.
$5.00
QTY:
2 LINES ENGRAVING
$6.50
QTY:
3 LINES ENGRAVING
$7.25
QTY:
Logo set-up charges $35. Engraving charges .18 per letter. After 1st use your logo is stored in our data vault for future use with no additional set-up charges. Above badge includes pin back although alternate attachments are available and listed below at additional cost. Above prices are for minimum orders of 100 + S&H & a maxium of 15 letters. Beveled corners (above right) are optional at .11 per badge.

 

Sublimation (above) is a process that basically uses special plastic material to act as a roll of film and apply a photographic image to the plastic. Thus, you can take a picture of just about anything and make it work for you to keep your corporate identification uniform wherever it appears...even on a name badge. Because the process applies the picture to the the plastic, no further engraving is required. Heat overlay or transfer is yet another way of applying a photo, logo or color scheme to the surface, however, when you engrave names through that surface material the inner core color of the plastic shows through. As an example, if the core color of the material used on the illustration above (STARZ HOUSE) was yellow, EMIL's name would appear in yellow. By selecting color coordinated inner cores and exteriors (and using the sublimation process or overlays) you are utilizing the 4-color process to it's maximum. Because Sublimation is a unique process, however, and special plastics are used, colors are limited. There is a one-time set up charge of $100 plus a $35 color charge to align the color registers. After your initial set-up, your image is stored for future use at no additional charge other than to align the color register.
Please call for custom quotes. (972) 345-0472

 

Metal "backers" provide a rigid base for any name badge as well as layering the badge to provide height and depth and a 3-D effect. Typically magnets are used to attach to garments although you can use pin, clip or military posts. Backers accommodate a plastic or metal badge approximately 1" x 3" and are good for simple one or two line engravings up to (and especially) customer logos and color processes as shown above. Backers are available in either Gold or Silver (each shown above) @ $1.45 ea.
DESCRIPTION
STYLE #
OVERALL SIZE (WxH)
ENGRAVABLE AREA
PRICE
METAL BACKERS
GOLD
1" X 3"
Because of the metal layering of the backers, no engraving is possible
$1.75
QTY:
SILVER
QTY:

Please enter all engraving instructions in the Pay Pay Billing Information Page, "Message to Seller" section or e-mail to info@naplenco.com

PIN-BACK (STD.)
SQUEEZE-BACK (OPT.)
MILITARY-BACK (OPT.)
OVER-POCKET (OPT.)
MAGNET (OPT.)
No Charge
.30 ea.
.40 ea.
*See below
.99 ea.
BADGE ATTACHMENTS
PRICE
ADD
PIN BACK
N/C
SQUEEZE-BACK
.30
QTY:
MILITARY-BACK
.40
QTY:
CLEAR PLASTIC OVER-POCKET
.76
QTY:
MAGNET
.99
QTY:
www.naplenco.com or call (972) 345-0472

 

* Over Pocket Badges are usually made from engravable material, not the clear shown above. Clear above is typically used as a backer/clip for badges where no clip, pin or magnet can be used either due to clothing material being too delicate or other material restrictions or, for application with a metal badge. Engraved over pocket badges (where the 1/2 plate above facing forward is on the outside of the pocket (as show in the below illustration) are sold as follows:
ENGRAVED OVER-POCKET BADGES
PRICE
1 Line Engraving No Logo Plus Material Cost
$4.00
QTY:
2 Lines Engraving No Logo Plus Material Cost
Add'l. .18 per letter (min. $1)
1 Line Engraving With Logo Plus Material Cost
$5.00
QTY:
2 Lines Engraving With Logo Plus Material Cost
Add'l. .18 per letter (min. $1)

ASK US FOR A QUOTE ON ANY SHAPE, ANY SIZE AND ANY AMOUNT.

CLICK HERE FOR COLOR CHOICES

CLICK HERE FOR CORPORATE LOGOS OR E-MAIL YOUR'S TO US @ info@naplenco.com

Please enter all engraving instructions in the Pay Pay Billing Information Page, "Message to Seller" section or e-mail to info@naplenco.com

National Plastic Engraving- Dallas, TX - Copyright © 2008 - All rights reserved · Terms of use - Privacy policy NAPLENCO P.O. Box 831664 Richardson, Texas 75083 Rev. 01/09